How to Sharpen a Chainsaw Chain: Step-by-Step Guide

November 16, 2026
How to Sharpen a Chainsaw Chain: Step-by-Step Guide - Person sharpening a chainsaw chain in a workshop.
Sharpening a chainsaw chain with a round file and file holder

A sharp chain cuts faster, safer and with less strain on your saw. This step-by-step guide shows you how to sharpen a chainsaw chain by hand with a round file, set the depth gauges and know when it's time for a new chain, with the right tools linked at every step.

A dull chain makes the saw work harder, produces fine dust instead of proper chips and increases the risk of kickback. The good news is that sharpening a chain by hand takes about ten minutes once you know how, and the tools cost less than a new chain.

This guide covers the whole job: choosing the right file, holding it at the correct angle, filing the cutters, lowering the depth gauges and checking your work. If you're still deciding whether your chain needs sharpening at all, our guide to why your chainsaw chain dulls so quickly explains the warning signs.

The Quick Answer

How long it takes

About 10 to 15 minutes

Two or three strokes per cutter, then a quick check of the depth gauges.

What you need

Round file, holder, depth gauge

The file diameter must match your chain pitch. The 2-in-1 Easy File covers the file and depth gauge in one tool.

How often

Little and often

A few strokes at every fuel stop keeps the edge sharp and avoids heavy filing later.

Before You Start: Safety

  • Switch the saw off and let it cool. For a battery saw, remove the battery.
  • Apply the chain brake or clamp the bar so the chain can't move while you file.
  • Wear gloves. Cutters are sharp even when they feel dull.
  • Work on a stable surface such as a bench with the bar clamped, or a stump vice in the field.
  • Check the chain tension before you start. A loose chain moves under the file and gives uneven results.

Know Your Chain: The Parts That Matter

Only two parts of the chain need your attention when sharpening: the cutters, which do the cutting, and the depth gauges (also called rakers), which control how deep each cutter bites. Sharpening the cutters without checking the depth gauges is the most common mistake.

Direction of travel Top plate (cutting edge) Depth gauge Drive link Cutter Tie straps and rivets join the links

Simplified side view of a saw chain. Not to scale.

Anatomy

What you're sharpening

Cutters alternate left and right along the chain. Each has a sharp top plate and side plate that slice through the wood.

Depth gauges sit just ahead of each cutter. If they're too tall, the cutter can't bite and the saw produces dust. If they're too low, the saw grabs and kicks.

Drive links sit in the bar groove and carry the chain round. You don't file these.

What You'll Need

You'll also need a flat file for the depth gauges if you aren't using the 2-in-1 Easy File, plus gloves and a way to hold the bar steady. Check each product page for the current stock in your chain size.

Step Zero: Choose the Right File Size

The file diameter has to match your chain's pitch. The pitch is usually stamped on the bar or printed on the chain packaging. A file that's too small won't reach the cutting edge properly, and one that's too large will damage the cutter.

Chain pitch Round file diameter
1/4" P 3.2 mm (1/8")
3/8" P (Picco) 4.0 mm (5/32")
.325" 4.8 mm (3/16")
3/8" 5.2 mm (13/64")
.404" 5.5 mm (7/32")

These are the standard sizes for STIHL and most other chains. Always check your chain's own specification if you're unsure.

See It in Action

How to Sharpen a Chainsaw Chain, Step by Step

Marked cutter (start here) Bar held steady, chain taut Clamp or vice

Hold the bar steady and mark your starting cutter. Schematic only.

STEP 1

Secure the saw and mark your starting cutter

Clamp the bar in a vice, or rest the saw on a stump with the chain brake on. Check the chain tension and pull the chain round by hand to make sure it moves freely.

Mark the first cutter with a marker pen so you know where you started. You'll file every cutter on one side, then turn the saw round and do the other.

Tip: a stump vice or bench clamp frees both hands for filing. Our sharpening and maintenance range includes clamps and holders.

STIHL chainsaw chain file gauge

The STIHL file gauge matches your chain to the right file.

STEP 2

Match the file to your chain

Use the table above to pick the right diameter. A file gauge takes the guesswork out, because you hold it against the chain and it shows you the correct file size.

Need spare files? STIHL round chainsaw files start from £1.58, and Oregon round files are available in packs of 12 for regular sharpeners.

Top plate About 1/5 of the file's diameter above the plate Side view, file end-on. Schematic.

Keep roughly a fifth of the file's diameter above the top plate.

STEP 3

Set the file height

Rest the file in the cutter's hollow with about one fifth of its diameter above the top plate. A file holder or the 2-in-1 Easy File sets this height for you, which is why they're recommended for first-timers.

Too high and you'll round off the cutting edge. Too low and you'll cut away too much of the cutter.

Shop File Holders
Guide bar Square to bar (90°) 30° File direction Top view. Typical STIHL angle shown.

Most STIHL chains use a 30° filing angle. Check your chain's specification.

STEP 4

Hold the correct filing angle

Keep the file level and angled to match the line stamped on the cutter. Most STIHL chains are filed at 30°, but some use 25° or 35°, so check your chain's specification before you start.

File from the inside of the cutter outwards, and keep the file the same angle on every tooth. An angle plate gives you a visual guide until your hands learn it.

Shop the Angle Plate
STIHL 2-in-1 Easy File sharpener resting on the chain

The 2-in-1 Easy File rests on the chain to hold both angle and height.

STEP 5

File each cutter with firm forward strokes

  • Push the file forwards only, from the inside of the cutter outwards. Lift the file on the return.
  • Make two to four strokes on each cutter, and use the same number on every one.
  • Roll the chain forwards a few links at a time. Work along all the cutters on one side.
  • Turn the saw round and repeat on the other side, matching the number of strokes.

Tip: every cutter should end up the same length. Match the shortest, most damaged cutter first, then file the rest to it.

Shop the 2-in-1 Easy File
File off what sticks through the slot Gauge sits flat on the cutters Schematic, not to scale

Only the part of the depth gauge poking above the tool needs filing.

STEP 6

Check and lower the depth gauges

Every second or third sharpen, check the depth gauges. Place the depth gauge tool over two cutters so the slot sits over the gauge. If any metal sticks through, file it level with the tool using a flat file, then lightly round off the front edge so it keeps its shape.

The STIHL depth gauge has two settings for hardwood and softwood, and most STIHL chains use a clearance of around 0.65 mm. Check your chain's specification for its exact figure.

Never over-file the gauges. Lowering them too far makes the saw grab and increases kickback risk.

Shop Depth Gauges
All cutters the same length Bright, clean cutting edges Depth gauges set correctly Test cut makes long chips, not dust

Your finished-job checklist.

STEP 7

Check your work and test the cut

Look along the chain. Every cutter should be the same length with a bright, clean edge. Refit the chain, check the tension and oil level, then make a test cut in a log.

A properly sharpened chain pulls itself into the wood and throws out long, curled chips. If you're still seeing fine dust, the cutters need another pass or the depth gauges need checking.

Not sure your oil and fuel are right for winter? Our guide to maintaining your chainsaw in cold weather covers it.

Common Sharpening Mistakes

  • Wrong file size. A file that's too small slides off the edge, and a large one damages the cutter.
  • Inconsistent strokes. Different stroke counts leave cutters at different lengths, so the saw cuts crooked and vibrates.
  • Filing the wrong angle. The saw pulls to one side and the chain wears unevenly.
  • Ignoring the depth gauges. A sharp cutter can't bite if the gauge is too high.
  • Over-filing. More strokes aren't better. Stop when you see a bright, fresh edge.
  • Sharpening a damaged chain. If cutters are cracked, bent or hit metal, file won't fix it. Replace the chain.

When to Stop Filing and Replace the Chain

Every sharpen removes a little metal. When the cutters are worn down to the wear mark on the top plate, or the top plate is only around 4 mm long, the chain has reached the end of its life. Cracked cutters, bent links or a chain that keeps pulling to one side are also signs to replace it. Our guide to choosing the right chainsaw chain shows you how to find the correct replacement.

Sharpening a Lot of Chains? Consider a Bench Grinder

Hand filing is ideal for field touch-ups. If you sharpen chains every week, a bench grinder is faster and gives consistent results.

Trusted UK Arborist Supplier

Professional-grade sharpening tools used by tree surgeons every day.

Authorised STIHL Dealer

Genuine STIHL files, gauges and guides, plus trusted brands like Oregon.

Expert Dealer Support

Not sure which file size you need? Ask us before you order.

Get Your Chain Cutting Like New

Files, holders, gauges and grinders, all in one place.

Shop Sharpening Tools

More Guides & Advice

Frequently Asked Questions

How often should I sharpen my chainsaw chain?

Touch up the cutters with a few strokes whenever you refuel, or as soon as the saw starts producing dust instead of chips. Little and often is easier than waiting until the chain is very dull.

What size file do I need for my chainsaw?

It depends on your chain pitch: 3.2 mm for 1/4" P, 4.0 mm for 3/8" P, 4.8 mm for .325", 5.2 mm for 3/8" and 5.5 mm for .404". A file gauge shows you the right size for your chain.

What angle should I file a chainsaw chain at?

Most STIHL chains are filed at 30°, but some use 25° or 35°. Follow the angle marked on your chain's cutters or in its specification, and keep it the same on every tooth.

Do I need to file the depth gauges every time?

No. Check them every second or third sharpen with a depth gauge tool, and file them only if they're sticking above the tool.

Is the STIHL 2-in-1 Easy File worth it?

For most people, yes. It holds the round file at the right height and angle and includes a flat file for the depth gauges, so it's the simplest way to learn. The files are replaceable, so the tool lasts.

How many times can I sharpen a chain?

Until the cutters reach the wear mark on the top plate, or the top plate is only around 4 mm long. After that the chain should be replaced.

How do I know the chain is sharp?

A sharp chain pulls itself into the wood with little pressure and produces long, curled chips. If you have to force the saw or it produces fine dust, it needs sharpening.

Shop this article

2-in-1 Easy File Chainsaw Sharpener
Vendor:
Stihl
Regular price
£35.17 Ex VAT
£42.20 Inc VAT
Sale price
£35.17 £35.17 Ex VAT
Regular price
£42.20 £42.20 Inc VAT
View Details
Chainsaw Chain Sharpening Tool Kit
Vendor:
Oregon
Regular price
£27.82 Ex VAT
£33.38 Inc VAT
Sale price
£27.82 £27.82 Ex VAT
Regular price
£33.38 £33.38 Inc VAT
View Details
FF 1 Chainsaw File Guide Holder
Vendor:
Stihl
Regular price
From £10.87 Ex VAT
£13.04 Inc VAT
Sale price
£10.87 From £10.87 Ex VAT
Regular price
£13.04 £13.04 Inc VAT
View Details
File Holder & Round File
Vendor:
Stihl
Regular price
£9.97 Ex VAT
£11.96 Inc VAT
Sale price
£9.97 £9.97 Ex VAT
Regular price
£11.96 £11.96 Inc VAT
View Details
Round Chainsaw Chain Files
Vendor:
Stihl
Regular price
£1.58 Ex VAT
£1.90 Inc VAT
Sale price
£1.58 £1.58 Ex VAT
Regular price
£1.90 £1.90 Inc VAT
View Details
Published  

shop our latest releases

Tree surgeon tools: STIHL equipment for tree care and maintenance on a sunny day in a lush garden.
STIHL

MACHINERY

Two tree surgeons in safety gear working in a wooded area, preparing branches for removal.
arborist

clothing & PPE

Tree surgeon working high in a tree, using ropes and safety gear to carry out tree maintenance.
arborist

climbing equipment